Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Double hung
Casement
Before
After
Before
After
Before
AfterGeometric & Shaped Windows in Westchester, FL | Winslow Windows & Doors
Geometric & Shaped Windows bring architectural character to Westchester homes without compromising hurricane protection. Think triangular gable accents, hexagonal transoms, octagonal focal points, and radius-topped curves. These aren’t generic stock units. Each one is fabricated to your exact opening. Winslow Windows & Doors has installed custom impact-rated shaped windows across Westchester for years, and we handle everything from the initial measurement through permit-ready documentation. If you’re planning a new build, a remodel, or replacing a dated fixed picture window, call (850) 721-1218 to talk through your options.
Product Overview - Geometric & Shaped Windows
Shaped windows do two jobs. They anchor a room’s visual identity, and they have to hold up under Florida’s wind loads. Most contractors treat those as separate concerns. We don’t. The Geometric & Shaped Windows we install in Westchester are custom-fabricated to your opening, in any configuration the design calls for. Triangular units above entry doors. Hexagonal windows in a stairwell. Octagonal centers in a great room. Curved or radius tops that echo a Mediterranean roofline.
What makes these suited to hurricane-prone construction comes down to the glazing and the frame engineering. Laminated impact glass with a PVB interlayer is standard. That interlayer is what holds the glass in the frame when something hits it, the same principle used in every impact product we carry. The frame, whether aluminum or vinyl, is extruded and reinforced to carry the design pressure your specific wind zone requires. You get the architectural detail without sacrificing the protection. That’s the entire point.
We see these windows most often in custom and semi-custom homes around Westchester where architects spec a shaped unit and the builder needs a product that will actually pass a Miami-Dade inspection. Winslow Windows & Doors carries and installs this profile across our PGT, CGI, CWS, ES Windows, ECO, and Mr-Glass lines, so we can match the right manufacturer to your frame material, finish, and lead-time needs rather than forcing one brand into every job.
Technical Specifications
Every shaped window we sell in Westchester starts with a site measurement, because these units are not forgiving of “close enough.” Here is what the product line offers:
- Frame materials: Aluminum or vinyl, depending on the look and structural requirement of the opening
- Maximum size: Custom fabricated to order, so there is no fixed cap on configuration
- Glass options: Laminated impact glass with PVB interlayer, Low-E insulated glass, tinted glass, clear glass
- Finish options: White, Almond, Bronze, Black, Tan
- Design pressure: Matched to your specific wind zone, up to +/-100, never higher
- Compliance documentation: Miami-Dade NOA and Florida Product Approval numbers available per configuration
- Code standard: Engineered to Florida Building Code High-Velocity Hurricane Zone requirements
Because the units are made to order, the spec sheet for one Westchester home will not look like the next. That’s expected. We confirm every detail on your quote before anything goes to fabrication.
Hurricane & Compliance Performance
Laminated Impact Glass
Laminated impact glass uses a PVB (polyvinyl butyral) interlayer to hold the glass in the frame under impact. Even if the glass fractures, the interlayer keeps the window in place, preventing wind and water intrusion. This is the core protective mechanism in every impact window we install in Westchester.
Miami-Dade NOA / Florida Product Approval
Miami-Dade NOA (Notice of Acceptance) and Florida Product Approval numbers are issued per configuration, not per product family. That means the specific shape, size, glass package, and frame combination you select must have its own approval. We verify that on your specific quote before you order.
FBC / HVHZ Compliance
These windows are engineered to Florida Building Code (FBC) High-Velocity Hurricane Zone (HVHZ) requirements. Miami-Dade County, which sets the HVHZ standard, is the strictest code environment in the country. Westchester sits inside that jurisdiction, and the products we install meet it.
TAS 201 / TAS 202 / TAS 203 Testing Context
HVHZ-rated products are tested under a specific protocol family. TAS 201 covers large-missile impact, TAS 202 covers cyclic wind-pressure loading, and TAS 203 covers forced-entry resistance. Any impact product that carries Miami-Dade approval has passed this testing sequence.
Design Pressure for Your Wind Zone
Design pressures are matched to your wind zone, up to +/-100, never higher. Some manufacturers rate their products at higher pressures because that is what the test achieved, not what your home requires. We match the rating to the actual requirement for your Westchester location.
Energy Performance
Low-E and insulated glass options are available for energy performance. Low-E coatings reduce solar heat gain through the glass, which matters in a Florida climate where the air conditioning runs most of the year. Tinted glass offers a similar heat-reduction benefit with a different aesthetic.
Color & Glass Options
The finish options, White, Almond, Bronze, Black, and Tan, cover most of what we see in Westchester architecture. White and Almond fit the clean coastal look. Bronze and Black have become popular on modern and transitional homes, where a dark window frame against a light stucco wall creates definition. Tan disappears into Spanish-Mediterranean facades with warm earth tones.
On the glass side, you have four directions to consider. Laminated impact glass is the workhorse, the protective layer that meets code. Clear glass gives you pure visibility and maximum natural light. Tinted glass cuts glare and solar heat, which matters on west-facing shaped windows in Westchester that catch afternoon sun. Low-E insulated glass combines the impact protection with the energy performance, and it is the option we suggest for larger shaped units on homes where energy use is a concern. Your quote will break out exactly which glass package applies to each shaped opening, because sometimes the right answer is different from one window to the next.
Installation by Winslow Windows & Doors in Westchester
A NOA-rated window is only as good as the installation around it. This is especially true for shaped units, where the frame has multiple angles, curved members, or radius corners that all need to be set correctly. Our installation process in Westchester starts with a pre-install inspection of the opening. Existing frames come out, and we check the rough opening for rot, out-of-square conditions, or structural problems before anything new goes in.
We set every window level, plumb, and square. On a shaped unit, that is not automatic, it takes shimming, measurement, and patience. The perimeter gets a low-expansion foam sealant applied per AAMA 812, which air-seals the gap without pushing the frame out of alignment. Installation practice follows AAMA 2400/2410 standards. Flashing details are handled to direct water away from the opening, not into the wall.
Westchester sits in a coastal exposure zone, so we pay close attention to the water management details. Every finished install gets a final water test before the interior trim goes back on. We clean up the site, haul away the old windows, and leave your property the way we found it, minus the openings we just replaced.
One more thing worth saying plainly. An improperly installed shaped impact window can fail inspection, leak during a storm, or both, even with a perfect NOA from the manufacturer. This is not a product to hand to a general labor crew. In Westchester, permit submittals for impact work typically require product approval documentation, and we are familiar with what those packages need to include. We will flag any approval or permitting issue before you order, not after the window arrives.
Frequently Asked Questions - Geometric & Shaped Windows
The design pressure is matched to your specific wind zone in Westchester, up to +/-100, never higher. We calculate the required rating based on your exact location, the size of the opening, and the building code requirements that apply, then verify the configured product meets it before ordering. Call (850) 721-1218 and we will confirm the rating for your home.
Lead time depends on the configuration, the manufacturer, and the glass package you choose. Because every geometric or shaped window is custom fabricated, you should expect longer than an off-the-shelf rectangular unit. We will give you a realistic production window on your quote, not an optimistic one. Call (850) 721-1218 to get an estimate and a timeline.
Yes, in Westchester, a permit for impact window installation typically requires the product approval documentation. NOA and Florida Product Approval numbers are issued per configuration, so the approval must match the exact size, shape, glass, and frame you are installing. We verify this on your quote and help with the submittal package. Call (850) 721-1218 with your plans and we will review them.
Yes, this product is custom fabricated to your opening. That includes triangular, hexagonal, octagonal, and curved configurations, in the size your design calls for. The limiting factor is structural, not catalog-based, meaning some very large shapes may require reinforcing or a different frame material. We will tell you what works before you order. Call (850) 721-1218 and we’ll review your opening dimensions.
Maintenance is simple. Wash the frames with mild soap and water, and check the perimeter sealant once a year for gaps or cracking. If you see separation at the sealant line, have it re-caulked before it becomes a water intrusion point. The impact glass itself does not need special treatment. Call (850) 721-1218 if you need a service check on existing shaped windows in your Westchester home.
Get a Quote - Geometric & Shaped Windows in Westchester
If you’re planning a project that calls for a shaped impact window, the sooner we see the plans or the opening, the sooner you will have a real number. We measure, we spec, we verify approvals, and we install it right. Call Winslow Windows & Doors at (850) 721-1218 to schedule a free on-site measurement, or to talk through your configuration ideas with someone who has done this in Westchester before.
Written by the team at Winslow Windows & Doors, serving Westchester, FL.
Six Reasons Homeowners Choose Winslow Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.
Other Winslow Windows & Doors Services
What Neighbors Say About Winslow Windows & Doors
Detailed Images
