Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Double hung
Casement
Before
After
Before
After
Before
AfterPGT Door Installation: The Westchester Owner’s Guide
PGT door installation in Westchester typically runs $450 to $1,400 installed, depending on whether you’re replacing hardware, a threshold, weather stripping, or the full door slab. We stock PGT-compatible parts on our trucks and can usually get most Westchester homeowners scheduled within a few days of their call. Most people discover they need us when the door starts dragging, the lock won’t catch, or daylight starts sneaking in around the frame after a good South Florida downpour.
Which PGT Models This Applies To
We install and service parts across the PGT lineup you’re most likely to find in Westchester homes built or renovated in the last 15 years: the WinGuard series (aluminum and vinyl impact doors), the ClassicVue, and the PremierVue sliding glass door lines. If your door was installed as part of a hurricane-protection upgrade, there’s a strong chance it’s a WinGuard, which uses a heavier-gauge frame and multi-point locking hardware that’s specific to PGT’s impact-rated design.
Here’s what you should know before you buy: PGT parts aren’t universal. The hinge screws, the roller assemblies, and especially the multi-point lock bodies vary by series and by the year the door was manufactured. A 2012 WinGuard hinge won’t always match a 2022 WinGuard. The quickest way to identify what you’ve got is to look for the PGT label on the door edge or in the frame track. It’ll show the series, the glass make-up, and a manufacturing code we can cross-reference. If that label’s worn off, we measure the frame, the hinge spacing, and the lock mortise to pin down the right match.
On the OEM-versus-aftermarket question: PGT’s OEM hardware is built to the same impact standard as the door, so we default to it. But there are quality aftermarket equivalents for things like rollers, weather stripping, and sweep seals that cost less and perform just as well in coastal conditions. We’ll tell you when the aftermarket part makes sense and when it doesn’t. Winslow Windows & Doors is an independent installer, not a PGT affiliate, so we stock what actually holds up in South Florida, not just what one catalog offers. We also keep parts for CGI, CWS, and ES Windows doors for the same reason.
One compatibility gotcha we see a lot in Westchester: homes with a mix of PGT windows and CGI doors because the previous owner replaced things in stages. If your door is CGI rather than PGT, don’t force PGT hardware on it. Different lock geometry, different roller profiles. Bring us a photo of the label and we’ll save you a wasted trip to a parts counter.
Signs Your PGT Door Installation Is Failing
- Door drags or scrapes the threshold. This usually means the rollers or the hinge-side shims have worn down. In Westchester’s heat, builder-grade roller bearings wear out faster than people expect, and once the door starts to sag, the lock and weather strip take the hit next.
- Lock lever turns but won’t throw the bolt. The multi-point lock rod inside the door edge has slipped or the gearbox inside the lock body is worn. This is a PGT-specific mechanism, and forcing the handle is a good way to snap the interior gear.
- Daylight or water at the bottom corners. The sweep seal and the threshold cap have flattened or the frame has settled. Water intrusion at the corners is the number one reason we replace PGT door thresholds in Westchester, especially on doors that face east and catch the afternoon storm lines.
- Door flexes when you push on it. On an impact door, flexing means the seal compression is off or the frame anchors have loosened. A PGT door that’s properly installed shouldn’t move more than a hair when you press the center of the panel.
- Condensation between the glass panes. The insulating glass unit has lost its seal. You’re looking at a glass replacement rather than a hardware fix, and on impact-rated doors in Westchester, this isn’t a job you want to put off through hurricane season.
Replacement Cost & What’s Included
In Westchester, most PGT door installation jobs we quote fall between $450 and $1,400. Here’s how that breaks down:
- Hardware replacement only (locks, hinges, handles, multi-point gearbox): $180-$420 parts and labor.
- Threshold and weather seal replacement: $220-$480 installed.
- Full door hardware refresh (all moving parts on an existing slab): $350-$650.
- Door slab replacement (same frame, new impact door panel): $900-$1,400 depending on glass and finish.
The biggest cost driver on slab replacements is whether you’re matching an existing impact rating and whether the frame is still square. If the frame’s solid, we keep it. If it’s not, we say so and show you what that looks like before we write anything up. Every quote is a line-item number, not a lump sum, so you see parts and labor separately. The work itself is warranted: if it’s not done right, we come back and make it right. That’s the Done Right Promise Ed Winslow put in writing, and it covers every PGT part we touch. There’s also $40 off any repair over $200, a free second opinion on any written estimate you’ve got from another company, and no trip charge if you’re here in the home county.
DIY or Call Us?
There’s a safe middle ground here, and then there’s the part where we’d rather you didn’t learn the hard way. You can clean the tracks, check the label for the model number, tighten visible hinge screws with a hand screwdriver, and take photos of anything that looks wrong. That’s genuinely useful before you call, and it helps us get the right parts on the truck the first time.
What we’d rather you not do is remove a PGT door slab. Impact doors run heavier than standard doors, often 150 pounds or more for a WinGuard with laminated glass. Removing one without a second person and proper blocking can do real damage to the door, the frame, or whoever’s unlucky enough to be standing there when the pins come out. If the door’s dragging, sagging, or leaking, call us at (850) 721-1218 and we’ll diagnose it honestly. If tightening screws is all it needs, we’ll say that and charge you accordingly. We’d rather earn a repair than sell you a door you don’t need.
FAQs
Hardware on a PGT door in Westchester typically lasts 10 to 15 years before rollers, lock bodies, or weather seals need replacement. After 15 years in this heat and salt air, budget for a full hardware refresh. The structural door slab itself can last decades if the frame’s installed correctly and the seals are maintained. Call (850) 721-1218 and we’ll tell you honestly whether you’re looking at a repair or a replacement.
Most of what fails on a PGT door is repairable: the hardware, the threshold, the seals, the lock body. We replace the slab only when the frame is compromised, the glass seal has failed, or the cost of repairing everything at once doesn’t make sense against new. Ed Winslow grew up in Westchester and has spent almost two decades telling homeowners the truth about which side of that line their door sits on. Estimates are free, so call us for a straight answer.
Hardware and seal replacement usually takes one to two hours on site. Full door slab replacement from a leading brand or an equivalent takes a half day, and most of that is final adjustment rather than brute labor. We’ll tell you the timeframe when we quote the work, and we hit it. Call (850) 721-1218 to schedule a free estimate and we can usually work around your schedule.
We keep common PGT rollers, locks, handles, thresholds, and weather seals on our trucks because Westchester homeowners should not have to wait two weeks for a door that won’t lock. We also stock parts for CGI, CWS, and ES Windows doors because homeowners rarely know which brand they have until somebody looks. If your part is unusual, we’ll tell you what the lead time is before you spend anything. Call (850) 721-1218 and tell us what’s going on with your door.
If your PGT door’s giving you trouble, or you just want a second opinion on a quote somebody else handed you, call (850) 721-1218. Ed’s name is on the truck. That means we stand behind every window and door we touch. The one down the road.
Written by Ed Winslow, Owner, Winslow Windows & Doors at Winslow Windows & Doors, serving Westchester and nearby areas.
Six Reasons Homeowners Choose Winslow Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.